OpenBuild’s Part Store: https://dflo.info/OpenBuilds
Dr. D-Flo’s Instagram: https://dflo.info/insta
Dr. D-Flo’s Thangs: https://dflo.info/Thangs
Links below may provide a small commission to support more CNC router content!
Equipment:
CNC Router: https://dflo.info/CNC-Router
Touch Interface: https://dflo.info/Interface
Probe: https://dflo.info/Probe
Table: https://dflo.info/Table
Enclosure: https://dflo.info/Enclosure
Tooling:
1/4″ Sq. Down-Cut 2 Flute: https://dflo.info/Endmill1
1/4” Sq. Up-Cut 1 Flute: https://dflo.info/Endmill2
1/4″ Ball Nose 2 Flute: https://dflo.info/Endmill3
1/8” Straight 2 Flute: https://dflo.info/Endmill4
1/16” Sq. Up-Cut 2 Flute: https://dflo.info/Endmill5
1/16” Sq. Up-Cut 1 Flute: https://dflo.info/Endmill6
Roundover Bit: https://dflo.info/Roundover
Flush Trim Bit: https://dflo.info/FlushBit
Workholding:
Painter’s Tape: https://dflo.info/PaintersTape
Super Glue + Activator: https://dflo.info/SuperGlue
Bessey Clamps: https://dflo.info/Clamps
Wood Glue: https://dflo.info/Wood-Glue
Glue Roller and Tray: https://dflo.info/Roller
Toe Clamp: https://dflo.info/Toe-Clamp
Finishing:
Orbital Sandpaper: https://dflo.info/Sanding
Sandpaper Sheets: https://dflo.info/SandSheets
Old Master’s Vanish: https://dflo.info/Varnish
Cutting Board:
Inlay Maple (6x12x1/16”): https://dflo.info/Maple
Citrus Finish (Oil + wax): https://dflo.info/CitrusFinish
Lavender Finish (Oil + wax): https://dflo.info/LavendarFinish
Table:
Table Legs: https://dflo.info/TableLegs
Trivet:
White Corian (8x12x1/2”): https://dflo.info/WhiteCorian
Walnut (6x12x1/2”) : https://dflo.info/Walnut
Silicone Adhesive: https://dflo.info/Silicone
Self-Adhesive Cork: https://dflo.info/Cork
Cookbook Stand:
Wireless Charging Unit: https://dflo.info/WirelessCharger
Maple (6x12x0.5”): https://dflo.info/Maple1
Black Corian (8x12x1/2”): https://dflo.info/BlackCorian
Inlay Maple (6x12x1/16”): https://dflo.info/Maple
Elastic Superglue: https://dflo.info/Med-Flex
Minimalistic Wallet:
Wallet Design from Etsy: https://dflo.info/wallet
Elastic Band: https://dflo.info/Elastic
1/8” Aluminum Plate: https://dflo.info/Al6061
Machinable Plate: https://dflo.info/Plate1
LED Sign:
Addressable LEDs: https://dflo.info/LED
Translucent Acrylic (12x24x1/8”): https://dflo.info/T-Acrylic
Sandable Primer: https://dflo.info/SandPrimer
Black Spray Paint: https://dflo.info/BlackPaint
Arduino Feather: https://dflo.info/Ard-Feather
Description: Out of all the different CNC machines that can be operated out of a garage, computer-controlled routers are arguably the most versatile. Capable of cutting not only wood but also plastics and non-ferrous metals, the CNC router can quickly turn a variety of materials into products that can be sold or gifted. Furniture and decorations are perhaps the most common creations that new hobbyists gravitate towards, but CNC routers are capable of so much more from cutting traces on a circuit boards to even engraving/cutting aluminum.
The best part about the CNC router is how low the barrier of entry is. The machine itself is light and only requires a common household voltage operate. The allowance for error are high because hobbyist grade machines, like the Lead 1010, are built to survive crashes as you learn the ins and outs of CNC programming.
If you’re not convinced that you need a CNC router in your home shop now then you will be after Dr. D-Flo covers his five favorite products to make in this video.
#DIY #CNC #Router
Table of Contents:
00:00 – Introduction
01:31 – Cutting Board
13:50 – Table w/ Inlay
14:38 – Trivets
22:03 – Polka Dot Trivet
23:03 – Cook Book Stand
30:11 – Wallet
35:50 – LED Sign
source
Comments are closed.